• 联系人:卢经理
  • 电话:0531-87416018
  • 手机:13853128178
  • 地址:济南市经十西路藤靳路
  • 口西2公里
新闻中心当前位置:首页-新闻中心
    使用卧式加工中心注意四大要点
    2020-2-20 14:41:10

    卧式加工中心是指工作台与主轴设置为平行状态的加工中心,卧式加工中心通常拥有三个直线运动坐标轴加一个工作台回转轴。卧式加工中心可以一次对工件夹装后,根据程序自主选择不同的刀具,自动改变主轴的转速,按编程顺序依次完成多个面上多个工序的加工,此类加工中心最适合加工箱体类零件。接下来小编介绍一下使用卧式加工中心注意四大要点。

    Horizontal machining center refers to the machining center whose worktable and spindle are set in parallel state. Horizontal machining center usually has three linear motion coordinate axes plus one worktable rotation axis. The horizontal machining center can select different tools according to the program, automatically change the rotation speed of the spindle, and finish the machining of multiple processes on multiple surfaces in sequence according to the programming sequence after clamping the workpiece at one time. This kind of machining center is most suitable for machining box type parts. Next, I will introduce four key points of using horizontal machining center.

    安装卧式加工中心的环境

    Installation environment of horizontal machining center

    卧式加工中心应该安装在远离震源、不要被阳光直射、没有热辐射和没有潮湿的地方。如果安装卧式加工中心的地方附近有震源,应该在卧式加工中心的周围设置防震沟。如果不设置防震沟会直接影响到卧式加工中心的加工精度以及稳定性,时间一久就会影响到电子元件接触不良,发生故障,影响卧式加工中心的可靠性。

    The horizontal machining center should be installed far away from the source, away from direct sunlight, without heat radiation and humidity. If there is a source near the place where the horizontal machining center is installed, the anti vibration ditch should be set around the horizontal machining center. If there is no shockproof groove, it will directly affect the machining accuracy and stability of horizontal machining center, and for a long time, it will affect the poor contact of electronic components, failure and reliability of horizontal machining center.

    琨鹏.jpg

    电压电流严格控制

    Strict control of voltage and current

    卧式加工中心一般都是安装在加工车间了,而加工车间的机械设备众多,难免导致电网波动大。所以卧式加工中心安装的位置必需严格控制电源的电压和电流,必需把电源的电压和电流控制在卧式加工中心允许范围之内,一定要保持电源的电压和电流稳定,否则会直接影响卧式加工中心的正常工作。

    Horizontal machining centers are generally installed in the processing workshop, and there are many mechanical equipment in the processing workshop, which inevitably leads to large fluctuations in the power grid. Therefore, the installation position of the horizontal machining center must strictly control the voltage and current of the power supply, the voltage and current of the power supply must be controlled within the allowable range of the horizontal machining center, and the voltage and current of the power supply must be kept stable, otherwise it will directly affect the normal operation of the horizontal machining center.

    温度和湿度会直接影响卧式加工中心

    Temperature and humidity will directly affect the horizontal machining center

    卧式加工中心一般要处于低于30摄氏度的环境下才能正常工作,一般情况下卧式加工中心的配电箱内都有设置排风扇和冷风机,以保证电子件和中央处理处于恒温状态下工作。如果温度和湿度过高会导致控制系统的元件寿命降低,导致卧式加工中心故障无故增多。湿度增高的话,灰尘就会在集成电路板上增多直接导致接触不良和短路的故障发生。

    The horizontal machining center can work normally only when the temperature is lower than 30 ℃. In general, the distribution box of the horizontal machining center is equipped with exhaust fan and cooling fan to ensure the electronic parts and central processing work under constant temperature. If the temperature and humidity are too high, the component life of the control system will be reduced, and the failure of the horizontal machining center will increase. If the humidity increases, the dust will increase on the integrated circuit board, which will directly lead to the failure of poor contact and short circuit.

    机床出厂参数设置

    Factory parameter setting of machine tool

    客户在使用卧式加工中心时,不能随意更改机床出厂参数设置,因为这些出厂参数设置直接关系卧式加工中心各个部件的动态特征,只有间隙补偿参数值可以根据实际情况来设置。如果要更改出厂设置参数应联系厂家,并在厂家技术人员指导下操作更改出厂参数设置。

    When using the horizontal machining center, the customer cannot change the factory parameter settings of the machine tool at will, because these factory parameter settings are directly related to the dynamic characteristics of each part of the horizontal machining center, only the gap compensation parameter values can be set according to the actual situation. If you want to change the factory setting parameters, you should contact the manufacturer and change the factory parameter settings under the guidance of the manufacturer's technical personnel.