• 联系人:卢经理
  • 电话:0531-87416018
  • 手机:13853128178
  • 地址:济南市经十西路藤靳路
  • 口西2公里
新闻中心当前位置:首页-新闻中心
    带锯床断线的处理方法!
    2019-12-19 14:34:11

      在用户运用带锯床一段时间后,由于缺乏维护而发作了一系列毛病。 由于锯床不够了解,毛病发作时会很担忧,设备毛病不会处理,这不只影响运用。 该单元的效率也将延迟整个施工期,这是十分费事的。 今天,描述下带锯床断线的问题以及如何处置。

      After using the band saw for a period of time, a series of problems occurred due to lack of maintenance. Due to the lack of understanding of the sawing machine, it will be very worried when the fault occurs, and the equipment fault will not be handled, which not only affects the use. The efficiency of the unit will also delay the whole construction period, which is very difficult. Today, describe the problem and how to deal with it.

      一,带锯床向块的磨损通常招致锯背磨损,招致程度锯带反面呈现裂痕,招致带断裂。 导块合金在锯背上会有明显的磨痕和凹槽。 带锯条在划痕上会有不规则的划痕和裂痕,所以要经常检查;

      First, the wear of the band sawing machine to the block usually leads to the wear of the saw back, leading to the degree that the reverse side of the band presents cracks, leading to the fracture of the band. The guide block alloy will have obvious wear marks and grooves on the saw back. The band saw blade will have irregular scratches and cracks on the scratches, so it should be checked frequently;

      二,带锯床上导块的间隙不适宜,招致锯反面压力过大,锯齿根部张力过大,产生裂纹 ,招致断裂带。 操作者首先调整两个圆盘的切割点,使两个锯臂缝在同一程度线上。 带锯锯条和肩部坚持距离,因而挡住纸张。 假如发现这种状况,及时处理;

    琨鹏.jpg

      Second, the gap between the guide blocks on the band sawing machine is not suitable, which leads to excessive pressure on the opposite side of the saw, excessive tension at the root of the saw tooth, cracks and fracture zones. The operator first adjusts the cutting points of the two discs so that the two saw arms are sewn on the same degree line. Band saw blade and shoulder stick to distance, thus blocking paper. If such a situation is found, handle it in time;

      三,带锯床的锯片由于太紧或太松而磨损,招致锯带的侧面被刮伤。 锯带上的负载太紧而不能断裂,但假如太松,锯带可能会偏转或切割会产生我的波纹;

      Third, the saw blade of the band sawing machine is worn because it is too tight or too loose, which causes the side of the band to be scratched. The load on the saw belt is too tight to break, but if it is too loose, the saw belt may deflect or cut to produce my ripples;

      四,带锯床速度和减速度不好,速度低,速度快,锯带负荷过大,招致皮带断裂,锯速快,速度慢,工作效率低,齿尖 早期磨损容易发作,因而影响锯床的运用寿命。

      Fourth, the speed and deceleration of the belt saw are not good, the speed is low, the speed is fast, the load of the saw belt is too large, which leads to the belt fracture, the saw speed is fast, the speed is slow, the working efficiency is low, the early wear of the tooth tip is easy to occur, thus affecting the service life of the saw machine.